How to Change a Pull Cord on a Lawn Mower

Replacing a pull cord can be a challenge especially if the recoil spring gets loose. Unscrew 3 or 4 of the screws that hold the starter assembly and the mower.

How To Easily Fix A Lawnmower Pull Start Cord Youtube Lawn Mower Mower Grass Mower

Dont let it retract.

. Clean the bearing rust using steel wool of a fine grade. DIY Bri shows you how to repair your lawn mower pull cord. How to replace the pull cord on a Briggs and Stratton lawnmower step-by-step.

Re-tension the Spring To achieve this you will need to wind the pulley in the opposite direction. Heat the knot a little bit with a match and pull it tight to keep it from coming undone. First things first using the appropriate screwdriver unscrew the screws that attach the pulley to its housing.

Unscrew the starter assembly. First push your mower to a clean flat surface so youll easily find any small part you drop. Process of replacing the pull cord on your Toro mower.

Unroll the old cord and take it of the disc. Locate and remove the three bolts that secure the starter cover to the top of the engine with a socket wrench. How much is a lawn mower pull cord.

Step 3Remove the Screws That Hold the Rewind Housing Together. Then remove the spark plug wire to be on the safe side and unhook the pull cord from the mower handle. Loosen the rope This will help you to remove the rope from the housing.

Push the end of the rope through both holes and tie a knot. This depends on how you want to return the rope to the housing. Remove all screws keeping the mowers housing in place.

Contents show 1 How To Replace Pull Cord On Lawn Mower. Take Out the Old Broken Rope. Tap the starter clutch cap and remove the cap and the assembly of the starter clutch.

Unscrew the cap that holds the pulley to the recoil starter housing. Do this by flipping the rewind unit and looking for a knotted portion. Make the Required Preparations.

Parts of a Mowers Pull Cord Housing. A small tab on the pulley can cut your hand if you accidentally let go of the recoil starter when it is tensioned. Pull the sparkplug wire off the top of the sparkplug with your fingers.

This is found on top of the lawn mower. Click to see full answer. Remove the old pull cord.

The procedure for this lawnmower will be the same on some Honda lawnmowers. Remove the spark plug and tilt the mower to drain out the oil. 12 Rewinding the pulley spring.

16 Refitting the pulley. Set The New Rope In Place. Get the correct replacement pull cord.

From the mower handle remove the pull cord. You may have some extra rope to cut off after everythings back together. Reassemble the lawnmower parts.

15 Inserting the new cord in the rewind unit. If you do you have to start over. Remove the screwdriver while you keep pressure on the pulley with your finger and gradually let the rope wind onto the wheel.

13 Taking off the damaged cord. Step 2Remove the Power Cord. Start by removing the old cord by rewinding it from the rewind unit.

Now its time to pull the cord completely out making sure the pulley is held firmly with your thumb. Just grab the knot and pull it out as far as it goes cut the remaining piece off. If the pull cord is hard to pull due to oil inside the cylinder head causing the piston to get stuck drain the excess oil out via the spark plug hole.

How to Replace a Pull Cord on Snapper Lawn Mower Turn the mower off and make sure it is on a flat surface. Easy to follow video tutorial on how to repair a broken lawnmower pull cord. When this is done the pulley will come out by itself by just lifting it off.

Now using both hands gently wind the pulley assembly counter-clockwise gradually until the tension tells you its fully wound. Replace Damaged Parts Parts like the pulley spring and the housing itself should be replaced if the need arises. 14 Preparing the replacement pull cord.

Follow these six steps to replace a lawnmower pullcord. Remove The Worn Out Pull Cord. Now you have to remove the knot that attaches the rope to the rewind unit.

Move the lawn mower to an even surface and unplug the spark plug. Remove the recoil housing cap. Drain out excess oil.

How to Replace a Pull Cord on a Mower. 10 Steps To Replace the Pull Cord 1. Tools Required to Replace a Pull Cord.

Replace the old pull cord with a new one. Lawn mower repair done on Honda Harmony 215 using universal pull start cord and handle from the H. Replace the spark plug and test whether the pull cord still has excessive drag.

Taming a recoil spring can be like herding cats. Remove the discs housing by unscrewing any fasteners. Replacing the cord requires the removal of the pull start assembly.

Reattach the disc cover by refastening all screws. Here is a basic step by step guide on how to replace your lawn mower pull cord. Nylon replacement rope is available at most home improvement centers.

Replacing a pull cord on a Briggs Stratton lawn mower requires removing the starter cover.

How To Repair The Pull Cord On A Lawnmower 554 Youtube

Lawn Mower Repair Broken Cord Diy Family Handyman

Fixing A Honda Mower Pull String W 550 Paracord Youtube